Okuma OSP Alarm Directory
Okuma Alarm B Codes
Request CNC Service
← Back to the Alarm Code Index
Okuma Alarm B Codes
(OSP-P300S / P300L)
Alarm B codes on Okuma CNC machines with OSP-P300S and OSP-P300L controls are typically related to machine operation, axis control, servo systems and motion functions. Select an alarm from the list below to view its meaning, possible causes and recommended diagnostic steps.
Experiencing this Okuma Alarm?
If your CNC machine is not operating normally, the alarm may require professional inspection of the control, drive or motion system.
Control diagnosticsParameter and PLC analysisOn-site repair
- Okuma Alarm B-2049 – PLC axis stroke end over
- Okuma Alarm B-2050 – PLC Axis Command Error
- Okuma Alarm B-2051 – PLC axis continuous positioning over
- Okuma Alarm B-2052 – Blue screen
- Okuma Alarm B-2053 – P100 Menu Error
- Okuma Alarm B-2058 – Error occurred while CAS work
- Okuma Alarm B-2059 – Non-functioning device detected
- Okuma Alarm B-2060 – Fan motor error on panel computer unit
- Okuma Alarm B-2090 – The remaining time after relocation has passed
- Okuma Alarm B-2092 – MCS Parameter learning error
- Okuma Alarm B-2114 – MCS Inertia identification error
- Okuma Alarm B-2120 – Overload detected.
- Okuma Alarm B-2132 – VDU communication error
- Okuma Alarm B-2133 – VDU detected error
- Okuma Alarm B-2134 – VDU initialization failure
- Okuma Alarm B-2135 – MCS DD encoder link error
- Okuma Alarm B-2136 – MCS DD Encoder error
- Okuma Alarm B-2137 – MCS DD Encoder (slave sensor) error
- Okuma Alarm B-2138 – MCS DD encoder initialization failure
- Okuma Alarm B-2139 – MCS DD encoder (slave sensor) initialization failure
- Okuma Alarm B-2144 – MCS Power supply unit overload
- Okuma Alarm B-2150 – MCS Undefined alarm number
- Okuma Alarm B-2151 – MCS Inverter unit fault
- Okuma Alarm B-2152 – Mistake in data from MCS to NC
- Okuma Alarm B-2153 – MCS CON APA deviation
- Okuma Alarm B-2154 – MCS Power supply unit error
- Okuma Alarm B-2155 – MCS Converter link error
- Okuma Alarm B-2156 – MCS DC-bus voltage alarm
- Okuma Alarm B-2157 – MCS Motor overcurrent
- Okuma Alarm B-2158 – MCS Power unit overheat
- Okuma Alarm B-2159 – MCS Power unit overload
- Okuma Alarm B-2160 – MCS Supply voltage flutter
- Okuma Alarm B-2161 – MCS Inverter capacity differs from spec.
- Okuma Alarm B-2162 – MCS Winding change failure
- Okuma Alarm B-2163 – MCS Encoder link error
- Okuma Alarm B-2164 – MCS Encoder detected error
- Okuma Alarm B-2165 – MCS Encoder initialization failure
- Okuma Alarm B-2166 – MCS Encoder with shaft detected error
- Okuma Alarm B-2167 – MCS Encoder with shaft initialization failure
- Okuma Alarm B-2168 – MCS ABSO SCALE error
- Okuma Alarm B-2169 – MCS ABSO SCALE initialization failure
- Okuma Alarm B-2170 – MCS Magnetic encoder alarm
- Okuma Alarm B-2171 – MCS Resolver alarm
- Okuma Alarm B-2172 – MCS Pulse generator count over
- Okuma Alarm B-2173 – MCS Motor overheat
- Okuma Alarm B-2174 – MCS Servo link error
- Okuma Alarm B-2175 – MCS Servo Link Disconnection
- Okuma Alarm B-2176 – Mistake in data from NC to MCS
- Okuma Alarm B-2177 – MCS Servo data error
- Okuma Alarm B-2178 – MCS Illegal command
- Okuma Alarm B-2179 – MCS CON speed over
- Okuma Alarm B-2180 – MCS Speed command over
- Okuma Alarm B-2181 – MCS DIFF over
- Okuma Alarm B-2182 – MCS APA speed over
- Okuma Alarm B-2183 – MCS Full-Closed APA Error
- Okuma Alarm B-2184 – MCS Over speed
- Okuma Alarm B-2185 – MCS Speed deviation over
- Okuma Alarm B-2186 – MCS Collision detected
- Okuma Alarm B-2187 – MCS Urgent-stop time over
- Okuma Alarm B-2188 – MCS Belt is broken
- Okuma Alarm B-2189 – MCS Axis change control error
- Okuma Alarm B-2190 – MCS Independent encoder initialization failure
- Okuma Alarm B-2191 – MCS Calculated current position lies outside range
- Okuma Alarm B-2192 – MCS Motor overload
- Okuma Alarm B-2194 – MCS ABSO SCALE sub-slider error
- Okuma Alarm B-2195 – MCS Tandem control communication error
- Okuma Alarm B-2196 – MCS Full abso scale link error
- Okuma Alarm B-2197 – MCS Full abso scale error
- Okuma Alarm B-2198 – MCS Full abso scale initialization failure
- Okuma Alarm B-2199 – MCS Axis stop signal error
- Okuma Alarm B-2200 – G-code error
- Okuma Alarm B-2201 – M-code error
- Okuma Alarm B-2202 – Common variable error
- Okuma Alarm B-2203 – System variable error
- Okuma Alarm B-2204 – Sequence name error
- Okuma Alarm B-2205 – Numeric data error
- Okuma Alarm B-2206 – Character use error
- Okuma Alarm B-2207 – Program name error
- Okuma Alarm B-2208 – Character string error
- Okuma Alarm B-2209 – Hexadecimal data error
- Okuma Alarm B-2210 – Spindle max revolution error
- Okuma Alarm B-2212 – G132/G133 command error
- Okuma Alarm B-2213 – Program factor over
- Okuma Alarm B-2214 – Subscript left side incorrect
- Okuma Alarm B-2215 – Local variable use over
- Okuma Alarm B-2216 – System variable setting data over
- Okuma Alarm B-2217 – Output variable setting data mistake
- Okuma Alarm B-2218 – UNUSABLE G-code
- Okuma Alarm B-2219 – UNUSABLE M-code
- Okuma Alarm B-2220 – Subscript left side illegal
- Okuma Alarm B-2221 – UNUSABLE output variable No
- Okuma Alarm B-2222 – UNUSABLE input variable No
- Okuma Alarm B-2223 – UNUSABLE turret direct code
- Okuma Alarm B-2224 – UNUSABLE contour generation command
- Okuma Alarm B-2225 – UNUSABLE Y-Z circle command
- Okuma Alarm B-2226 – UNUSABLE thread cutting command
- Okuma Alarm B-2227 – Mnemonic or local variable mistake
- Okuma Alarm B-2228 – VSET sequence left command mistake
- Okuma Alarm B-2229 – EXPRESSION right side
- Okuma Alarm B-2230 – EXPRESSION calculation error
- Okuma Alarm B-2231 – EXPRESSION syntax incorrect
- Okuma Alarm B-2232 – EXPRESSION subscript mistake
- Okuma Alarm B-2233 – EXPRESSION buffer over
- Okuma Alarm B-2234 – EXPRESSION local variable
- Okuma Alarm B-2235 – Equal does not exist
- Okuma Alarm B-2236 – Program End Code Not Found
- Okuma Alarm B-2237 – BRANCH (IF,GOTO) sequence name
- Okuma Alarm B-2238 – BRANCH(IF,GOTO) condition
- Okuma Alarm B-2239 – Mistake in F command
- Okuma Alarm B-2240 – Mistake in F/E command
- Okuma Alarm B-2241 – Mistake in I command
- Okuma Alarm B-2242 – Mistake in J command
- Okuma Alarm B-2243 – Mistake in K command
- Okuma Alarm B-2244 – Mistake in L command
- Okuma Alarm B-2245 – Mistake in P command
- Okuma Alarm B-2246 – Mistake in S command
- Okuma Alarm B-2247 – No S command
- Okuma Alarm B-2248 – Mistake in T command
- Okuma Alarm B-2249 – Mistake in X command
- Okuma Alarm B-2250 – Mistake in X/Z command
- Okuma Alarm B-2251 – Mistake in Z command
- Okuma Alarm B-2252 – Mistake in arc command
- Okuma Alarm B-2253 – Mistake in angle command
- Okuma Alarm B-2254 – Mistake in thread cutting cycle command
- Okuma Alarm B-2255 – Mistake in arc radius command
- Okuma Alarm B-2256 – Mistake in D command
- Okuma Alarm B-2257 – Mistake in gauging cycle command
- Okuma Alarm B-2258 – Mistake in C command
- Okuma Alarm B-2259 – Mistake in SB command
- Okuma Alarm B-2260 – Mistake in QA command
- Okuma Alarm B-2261 – Mistake in X/Y command
- Okuma Alarm B-2262 – Mistake in incremental command
- Okuma Alarm B-2263 – Command required for X-, Y-axes
- Okuma Alarm B-2264 – Mistake in Y command
- Okuma Alarm B-2265 – Distance calculation over limit
- Okuma Alarm B-2266 – Mistake in R command
- Okuma Alarm B-2267 – Mistake in drilling cycle command
- Okuma Alarm B-2268 – Mistake in angle command
- Okuma Alarm B-2269 – Angle chamfering command error
- Okuma Alarm B-2270 – Mistake in CD command
- Okuma Alarm B-2271 – Mistake in CL command
- Okuma Alarm B-2272 – Mistake in TM command
- Okuma Alarm B-2273 – Mistake in W command
- Okuma Alarm B-2274 – Mistake in CB command
- Okuma Alarm B-2275 – Mistake in HP command
- Okuma Alarm B-2276 – Mistake in CC command
- Okuma Alarm B-2277 – Mistake in torque limit command
- Okuma Alarm B-2278 – SUB PROGRAM repetition
- Okuma Alarm B-2279 – SUB PROGRAM stack
- Okuma Alarm B-2280 – SUB PROGRAM program name
- Okuma Alarm B-2281 – SUB PROGRAM data print
- Okuma Alarm B-2282 – SCHEDULE PROGRAM ‘Q’
- Okuma Alarm B-2283 – SCHEDULE PROGRAM mnemonic code
- Okuma Alarm B-2284 – SCHEDULE PROGRAM program end
- Okuma Alarm B-2285 – SCHEDULE PROGRAM main program load
- Okuma Alarm B-2286 – Plus variable limit over
- Okuma Alarm B-2287 – Minus variable limit over
- Okuma Alarm B-2288 – User reserve code
- Okuma Alarm B-2289 – Unable to Write Backup Data File
- Okuma Alarm B-2290 – Program name not selected
- Okuma Alarm B-2291 – Main sequence error
- Okuma Alarm B-2292 – Restart failure
- Okuma Alarm B-2293 – MDI special G-code
- Okuma Alarm B-2294 – Special G-code table
- Okuma Alarm B-2295 – STM time over
- Okuma Alarm B-2296 – UGC No program end code
- Okuma Alarm B-2297 – UGC DELETE syntax
- Okuma Alarm B-2298 – UGC DEF syntax
- Okuma Alarm B-2299 – UGC TIP syntax
- Okuma Alarm B-2300 – UGC TIF syntax
- Okuma Alarm B-2301 – UGC No shape entry
- Okuma Alarm B-2302 – UGC Illegal numerical data
- Okuma Alarm B-2303 – UGC Illegal character
- Okuma Alarm B-2304 – UGC User variable
- Okuma Alarm B-2305 – UGC System variable
- Okuma Alarm B-2306 – UGC Illegal command
- Okuma Alarm B-2307 – UGC Program factor over
- Okuma Alarm B-2308 – UGC Coordinate data
- Okuma Alarm B-2309 – UGC END syntax
- Okuma Alarm B-2310 – UGC Command over
- Okuma Alarm B-2311 – UGC Command format
- Okuma Alarm B-2312 – UGC Additional parameter
- Okuma Alarm B-2313 – UGC Expression
- Okuma Alarm B-2314 – UGC Figure entry area over
- Okuma Alarm B-2315 – UGC Unable to delete
- Okuma Alarm B-2316 – READ/WRITE No spec
- Okuma Alarm B-2317 – READ/WRITE Buffer over
- Okuma Alarm B-2318 – READ/WRITE Device No.
- Okuma Alarm B-2319 – READ/WRITE Data
- Okuma Alarm B-2320 – READ communication error
- Okuma Alarm B-2321 – WRITE communication error
- Okuma Alarm B-2322 – GET/PUT No spec.
- Okuma Alarm B-2323 – GET/PUT Buffer over
- Okuma Alarm B-2324 – GET/PUT Number of digits
- Okuma Alarm B-2325 – GET/PUT Variable designation
- Okuma Alarm B-2326 – GET Numerical data
- Okuma Alarm B-2327 – Calculation function no spec.
- Okuma Alarm B-2328 – Sub-program no spec.
- Okuma Alarm B-2329 – Sub-spindle interference distance
- Okuma Alarm B-2330 – Input/output variable no spec.
- Okuma Alarm B-2331 – Multiple machining no spec.
- Okuma Alarm B-2332 – Sub-spindle no spec.
- Okuma Alarm B-2334 – In-process gauging no spec.
- Okuma Alarm B-2335 – Post-process gauging no spec.
- Okuma Alarm B-2336 – Animation no spec.
- Okuma Alarm B-2337 – Graphic backup data file write failure
- Okuma Alarm B-2338 – Spindle orientation no spec.
- Okuma Alarm B-2339 – Load monitor no spec.
- Okuma Alarm B-2340 – Thread phase matching no spec.
- Okuma Alarm B-2341 – Circular thread cutting no spec.
- Okuma Alarm B-2343 – Tool retract no spec.
- Okuma Alarm B-2344 – Tool retract interrupt enable com.
- Okuma Alarm B-2345 – Tool retract interrupt disable com.
- Okuma Alarm B-2346 – Tool retract interrupt return com.
- Okuma Alarm B-2347 – ROBOT no spec.
- Okuma Alarm B-2348 – ROBOT program name
- Okuma Alarm B-2349 – LOADER no spec.
- Okuma Alarm B-2350 – LOADER program name
- Okuma Alarm B-2351 – Coupling device program select no spec.
- Okuma Alarm B-2353 – CHAMFERING G01 mode
- Okuma Alarm B-2354 – CHAMFERING L over
- Okuma Alarm B-2355 – CHAMFERING L illegal order
- Okuma Alarm B-2356 – CHAMFERING X, Z illegal order
- Okuma Alarm B-2357 – CHAMFERING Any angle calculation
- Okuma Alarm B-2358 – CHAMFERING Any angle
- Okuma Alarm B-2359 – NOSE-R COMP. No spec.
- Okuma Alarm B-2360 – NOSE-R COMP. NOSE-R > circle-R
- Okuma Alarm B-2361 – NOSE-R COMP. Calculation
- Okuma Alarm B-2362 – Nose-R Compensation Cancel (G40) Only Allowed in G00 or G01
- Okuma Alarm B-2363 – NOSE-R COMP. No cross point
- Okuma Alarm B-2364 – NOSE-R COMP. Entrance command error
- Okuma Alarm B-2365 – NOSE-R COMP. Thread cutting cycle
- Okuma Alarm B-2366 – TOOL RADIUS COMP. No spec.
- Okuma Alarm B-2367 – TOOL RADIUS COMP. NOSE-R comp. surface change
- Okuma Alarm B-2368 – TOOL RADIUS COMP. C-axis separation
- Okuma Alarm B-2369 – TOOL RADIUS COMP. QA command
- Okuma Alarm B-2370 – TOW-ALONG TAILSTOCK MOVEMENT no spec.
- Okuma Alarm B-2371 – TOW-ALONG TAILSTOCK MOVEMENT condition
- Okuma Alarm B-2372 – LASER MEASUREMENT no spec.
- Okuma Alarm B-2373 – LASER MEASUREMENT condition
- Okuma Alarm B-2374 – LAP No spec.
- Okuma Alarm B-2375 – LAP B illegal order
- Okuma Alarm B-2376 – LAP D illegal order
- Okuma Alarm B-2377 – LAP DA(DB) illegal order
- Okuma Alarm B-2378 – LAP H illegal order
- Okuma Alarm B-2379 – LAP H-U(W) < D (M73)
- Okuma Alarm B-2380 – LAP U(W) illegal order
- Okuma Alarm B-2381 – LAP U(W) > H
- Okuma Alarm B-2382 – LAP XA(ZA), XB(ZB) illegal order
- Okuma Alarm B-2383 – LAP Calculation error
- Okuma Alarm B-2384 – LAP Down step number over
- Okuma Alarm B-2385 – LAP Entry in LAP
- Okuma Alarm B-2386 – LAP Sequence name
- Okuma Alarm B-2387 – Unable to LAP Control
- Okuma Alarm B-2388 – LAP No G-code
- Okuma Alarm B-2389 – LAP NOSE-R comp. cancel
- Okuma Alarm B-2390 – LAP Entry in NOSE-R comp.
- Okuma Alarm B-2391 – LAP Shape designation
- Okuma Alarm B-2392 – MULTI CYCLE B illegal order
- Okuma Alarm B-2393 – MULTI CYCLE D illegal order
- Okuma Alarm B-2394 – MULTI CYCLE F illegal order
- Okuma Alarm B-2395 – MULTI CYCLE H illegal order
- Okuma Alarm B-2396 – MULTI CYCLE H-U(W) < D (M73)
- Okuma Alarm B-2396 – Multi Cycle H-U(W) < D (M73)
- Okuma Alarm B-2397 – MULTI CYCLE I,K over
- Okuma Alarm B-2398 – MULTI CYCLE I,K illegal order
- Okuma Alarm B-2399 – MULTI CYCLE L illegal order
- Okuma Alarm B-2400 – MULTI CYCLE Entry in LAP
- Okuma Alarm B-2401 – MULTI CYCLE U(W) illegal order
- Okuma Alarm B-2402 – MULTI CYCLE U(W) > H
- Okuma Alarm B-2403 – MULTI CYCLE X,Z illegal order
- Okuma Alarm B-2404 – MULTI CYCLE Angle
- Okuma Alarm B-2405 – MULTI CYCLE Tool offset
- Okuma Alarm B-2406 – MULTI CYCLE Cycle start point
- Okuma Alarm B-2407 – MULTI CYCLE Entry in NOSE-R comp.
- Okuma Alarm B-2408 – MULTI CYCLE Width
- Okuma Alarm B-2409 – TOOL LIFE CONTROL no spec.
- Okuma Alarm B-2410 – Tool life management No spare tool
- Okuma Alarm B-2411 – TOOL LIFE CONTROL tool group
- Okuma Alarm B-2412 – TOOL LIFE CONTROL no T-entry
- Okuma Alarm B-2413 – TOOL LIFE CONTROL tool offset group
- Okuma Alarm B-2414 – TOOL LIFE CONTROL no T-offset
- Okuma Alarm B-2415 – MULTI-MACHINING CYCLE No spec.
- Okuma Alarm B-2416 – MULTI-MACHINING CYCLE C
- Okuma Alarm B-2417 – MULTI-MACHINING CYCLE I,K
- Okuma Alarm B-2418 – MULTI-MACHINING CYCLE Q
- Okuma Alarm B-2419 – MULTI-MACHINING CYCLE F
- Okuma Alarm B-2420 – MULTI-MACHINING CYCLE L
- Okuma Alarm B-2421 – MULTI-MACHINING CYCLE D
- Okuma Alarm B-2422 – Multi-Machining Cycle X, Z
- Okuma Alarm B-2423 – MULTI-MACHINING CYCLE SA
- Okuma Alarm B-2424 – Multi-Machining Cycle (G185–G188) Used in G94 Mode
- Okuma Alarm B-2425 – MULTI-MACHINING CYCLE A
- Okuma Alarm B-2426 – MULTI-MACHINING CYCLE Thread cycle
- Okuma Alarm B-2427 – MULTI-MACHINING CYCLE U,W
- Okuma Alarm B-2428 – MULTI-MACHINING CYCLE SB
- Okuma Alarm B-2429 – MULTI-MACHINING CYCLE Y-axis mode
- Okuma Alarm B-2430 – ATC no spec.
- Okuma Alarm B-2431 – ATC syntax
- Okuma Alarm B-2432 – ATC TC
- Okuma Alarm B-2434 – ATC TL
- Okuma Alarm B-2435 – ATC MT
- Okuma Alarm B-2436 – ATC MG
- Okuma Alarm B-2438 – Unable to M06/M228 command
- Okuma Alarm B-2440 – Y-axis no spec.
- Okuma Alarm B-2441 – 2 saddle machine no spec.
- Okuma Alarm B-2444 – Carrier axis variable limit over
- Okuma Alarm B-2445 – 3-D coordinate conversion
- Okuma Alarm B-2456 – W-axis minus variable limit over
- Okuma Alarm B-2457 – X-axis correction stroke end over
- Okuma Alarm B-2459 – Restart axis position is illegal
- Okuma Alarm B-2460 – Change timing G13/G14
- Okuma Alarm B-2462 – Change timing G122/G123
- Okuma Alarm B-2463 – Change timing G140/G141/G142
- Okuma Alarm B-2464 – Spindle/turret G-code
- Okuma Alarm B-2465 – G122/G123 command mismatch
- Okuma Alarm B-2466 – Unable to Issue M100 Command During Nose-R Compensation
- Okuma Alarm B-2472 – Y-axis control mode
- Okuma Alarm B-2475 – W-axis command G-code
- Okuma Alarm B-2476 – Mirror image coordinate selection
- Okuma Alarm B-2477 – Sub-spindle mode
- Okuma Alarm B-2478 – No workpiece coordinate mode command
- Okuma Alarm B-2479 – Contour generation calculation error
- Okuma Alarm B-2480 – G132/G133 command error
- Okuma Alarm B-2486 – NC turret no spec.
- Okuma Alarm B-2487 – Unable to select coordinates
- Okuma Alarm B-2488 – UNUSABLE X-axis command
- Okuma Alarm B-2489 – NC tailstock parameter error
- Okuma Alarm B-2490 – Chuck pressure out of range
- Okuma Alarm B-2492 – Interrupt program: illegal command
- Okuma Alarm B-2493 – Linked external equipment program selection
- Okuma Alarm B-2494 – Chuck pressure command illegal
- Okuma Alarm B-2495 – Inverse time feed command format
- Okuma Alarm B-2496 – CAM data cannot be transmitted.
- Okuma Alarm B-2497 – T code
- Okuma Alarm B-2498 – Learning cannot be executed.
- Okuma Alarm B-2499 – Spindle marker latch data error
- Okuma Alarm B-2500 – MULTI-MACHINING CYCLE HS,HI,HJ,HK
- Okuma Alarm B-2501 – Recovering synchronous error
- Okuma Alarm B-2502 – Block Delete command error
- Okuma Alarm B-2503 – End sequence name error
- Okuma Alarm B-2504 – PREMIUM THREAD Command error
- Okuma Alarm B-2505 – CAM machine no spec.
- Okuma Alarm B-2506 – Tool center point control not possible
- Okuma Alarm B-2507 – CHP command error
- Okuma Alarm B-2508 – Machining mode command format
- Okuma Alarm B-2509 – MULTI-MACHINING CYCLE Return point
- Okuma Alarm B-2510 – Mistake in torque skip cycle command
- Okuma Alarm B-2511 – Remote buffer operation
- Okuma Alarm B-2512 – M-tool spindle overload
- Okuma Alarm B-2513 – Coordinate calculation
- Okuma Alarm B-2514 – MULTI CYCLE C-axis shift
- Okuma Alarm B-2515 – Remote buffer operation time out
- Okuma Alarm B-2516 – Remote buffer operation communication error
- Okuma Alarm B-2517 – W-axis control mode
- Okuma Alarm B-2518 – Synchronized tapping command
- Okuma Alarm B-2519 – Tailstock control command
- Okuma Alarm B-2520 – Mistake in TP command
- Okuma Alarm B-2521 – Mistake in BT command
- Okuma Alarm B-2522 – Mistake in BA command
- Okuma Alarm B-2523 – Thermistor error
- Okuma Alarm B-2524 – Mistake in AT command
- Okuma Alarm B-2525 – Chuck coordinate change condition
- Okuma Alarm B-2528 – Program selection unsuitable
- Okuma Alarm B-2529 – Thermal deviation compensation
- Okuma Alarm B-2530 – Machining process instruction no.
- Okuma Alarm B-2531 – Mirror turning mode
- Okuma Alarm B-2532 – System variable set condition error
- Okuma Alarm B-2533 – Steady rest over interference pos.
- Okuma Alarm B-2534 – LBB turret rotation impossible
- Okuma Alarm B-2536 – Coordinate movement rotation copy
- Okuma Alarm B-2537 – SLANT PROCESS MODE
- Okuma Alarm B-2538 – Incorrect system variable
- Okuma Alarm B-2539 – Mistake in B command
- Okuma Alarm B-2541 – PROGRAM PRINT command
- Okuma Alarm B-2542 – Feed axis retract function command
- Okuma Alarm B-2543 – Turret Index Error Position
- Okuma Alarm B-2544 – TOOL-ID TOOL DATA
- Okuma Alarm B-2545 – MULTI-MACHINING CYCLE LD
- Okuma Alarm B-2546 – MULTI-MACHINING CYCLE LK
- Okuma Alarm B-2547 – No decimal point
- Okuma Alarm B-2548 – X-, Z-axis synchronized feed mode
- Okuma Alarm B-2549 – Tool no. mismatch after ATC sequence restart
- Okuma Alarm B-2550 – Home position no spec.
- Okuma Alarm B-2551 – External home position command
- Okuma Alarm B-2552 – Barrier area
- Okuma Alarm B-2555 – Linear guide cover interference area command
- Okuma Alarm B-2557 – Illegal steady rest command
- Okuma Alarm B-2558 – Turning position selection
- Okuma Alarm B-2559 – Attachment rotation not possible
- Okuma Alarm B-2561 – Illegal system command variable
- Okuma Alarm B-2562 – Tool posture fluctuation reduction
- Okuma Alarm B-2563 – Mistake in TE command
- Okuma Alarm B-2564 – Index disable position
- Okuma Alarm B-2565 – Load monitor system variable
- Okuma Alarm B-2566 – MULTI-MACHINING CYCLE No M-tool cycle command
- Okuma Alarm B-2567 – No helical cutting specifications
- Okuma Alarm B-2568 – Mistake in OF command
- Okuma Alarm B-2569 – Thermal deviation comp. backup failure
- Okuma Alarm B-2570 – W-axis position condition
- Okuma Alarm B-2571 – W-axis position no spec.
- Okuma Alarm B-2572 – Mistake in RC command
- Okuma Alarm B-2573 – Taper cutting cycle
- Okuma Alarm B-2575 – Mistake in ‘TD’,’TDG’,’OS’ commands
- Okuma Alarm B-2576 – Mistake in H command
- Okuma Alarm B-2577 – No axis movement command
- Okuma Alarm B-2578 – NO D COMMAND
- Okuma Alarm B-2579 – NO L COMMAND
- Okuma Alarm B-2580 – Mistake in XS command
- Okuma Alarm B-2581 – CAM data deployment mode
- Okuma Alarm B-2582 – CAM data file write protect
- Okuma Alarm B-2583 – Compensation value overflow
- Okuma Alarm B-2584 – CON speed XS-axis
- Okuma Alarm B-2585 – XS-axis command turret mode
- Okuma Alarm B-2586 – Synchronous mode execution impossible
- Okuma Alarm B-2587 – No A command
- Okuma Alarm B-2588 – Mistake in OF command
- Okuma Alarm B-2589 – Definition conditions
- Okuma Alarm B-2590 – Y-axis command
- Okuma Alarm B-2591 – Mistake in point command
- Okuma Alarm B-2593 – Mistake in CF command
- Okuma Alarm B-2594 – Mistake in RJ command
- Okuma Alarm B-2595 – Synchronized rotation speed over
- Okuma Alarm B-2596 – Synchronized tap overload
- Okuma Alarm B-2597 – G15 Command Issued Outside Transportation Mode
- Okuma Alarm B-2598 – No Spec code. “Tool information management spec”
- Okuma Alarm B-2599 – Command not possible while mounting LBB.
- Okuma Alarm B-2602 – SCHEDULE PROGRAM main program load
- Okuma Alarm B-2603 – Spindle rotation fluctuation control no spec.
- Okuma Alarm B-2604 – Tow-along steady rest no spec.
- Okuma Alarm B-2605 – Tow-along tailstock no spec.
- Okuma Alarm B-2606 – READ/WRITE file open
- Okuma Alarm B-2607 – Mistake in AP command
- Okuma Alarm B-2608 – Mistake in ON command
- Okuma Alarm B-2609 – A-axis control no spec.
- Okuma Alarm B-2610 – Zero offset select inpossible
- Okuma Alarm B-2611 – Spindle fluctuation control no spec.
- Okuma Alarm B-2612 – Mistake in TR command
- Okuma Alarm B-2613 – Mistake in MTM command
- Okuma Alarm B-2614 – Mistake in MTS command
- Okuma Alarm B-2615 – Mistake in MGS command
- Okuma Alarm B-2616 – B-axis mode
- Okuma Alarm B-2617 – Zero setting condition
- Okuma Alarm B-2618 – Workpiece detection sensor not ready
- Okuma Alarm B-2619 – Mistake in SW command
- Okuma Alarm B-2622 – Unset system variable read
- Okuma Alarm B-2623 – B-axis no spec.
- Okuma Alarm B-2624 – Tow-along steady rest type-B no spec
- Okuma Alarm B-2625 – Tow-along steady rest movement condition
- Okuma Alarm B-2626 – W-axis overlap
- Okuma Alarm B-2628 – Mistake in TW command
- Okuma Alarm B-2629 – Mistake in FW command
- Okuma Alarm B-2630 – Mistake in SC command
- Okuma Alarm B-2631 – DNC-DT Path name
- Okuma Alarm B-2632 – DNC-DT Program select
- Okuma Alarm B-2633 – DNC-DT Preload error
- Okuma Alarm B-2634 – DNC-DT Delete error
- Okuma Alarm B-2635 – Y-axis mode
- Okuma Alarm B-2637 – No axis movement command
- Okuma Alarm B-2639 – Unable to issue C-axis command during helical cutting
- Okuma Alarm B-2640 – AC thread rotation count error
- Okuma Alarm B-2641 – AC thread fluctuation control not possible
- Okuma Alarm B-2642 – READ/WRITE No empty SAT
- Okuma Alarm B-2643 – READ/WRITE File open
- Okuma Alarm B-2644 – Unusable PRINT request
- Okuma Alarm B-2645 – YS-axis position
- Okuma Alarm B-2646 – SYSTEM VARIABLE C-axis separation
- Okuma Alarm B-2648 – MG tool ready cycle no spec.
- Okuma Alarm B-2649 – SYSTEM VARIABLE Y-axis mode
- Okuma Alarm B-2650 – SYSTEM VARIABLE B-axis mode
- Okuma Alarm B-2651 – C-axis multi rotation mode
- Okuma Alarm B-2652 – Mistake in HA command
- Okuma Alarm B-2653 – Mistake in MN command
- Okuma Alarm B-2654 – Hob circular cutting command
- Okuma Alarm B-2655 – Hob cutting command
- Okuma Alarm B-2657 – SYSTEM VARIABLE C-axis connect
- Okuma Alarm B-2659 – NC tailstock position error
- Okuma Alarm B-2662 – NC TAILSTOCK no spec.
- Okuma Alarm B-2663 – Turning cut condition interlock
- Okuma Alarm B-2667 – X-axis mirror image coordinates selected
- Okuma Alarm B-2668 – X-axis mirror image coordinates impossible
- Okuma Alarm B-2671 – C-axis sync control no spec.
- Okuma Alarm B-2672 – C-axis sync command format
- Okuma Alarm B-2674 – Default status macro cannot be executed
- Okuma Alarm B-2675 – Tool posture command error
- Okuma Alarm B-2676 – Tool posture command angle conversion error
- Okuma Alarm B-2677 – Attachment change not possible
- Okuma Alarm B-2678 – SPM contour control not possible
- Okuma Alarm B-2679 – Mistake in Q command
- Okuma Alarm B-2682 – Magnetic encoder speed detection error
- Okuma Alarm B-2683 – MCS Rotary encoder 5 initialization failure
- Okuma Alarm B-2684 – MCS Rotary encoder 5 error
- Okuma Alarm B-2685 – MCS Rotary encoder 4 initialization failure
- Okuma Alarm B-2686 – MCS Rotary encoder 4 error
- Okuma Alarm B-2687 – MCS Rotary encoder 3 initialization failure
- Okuma Alarm B-2688 – MCS Rotary encoder 3 error
- Okuma Alarm B-2689 – MCS Rotary encoder 2 error
- Okuma Alarm B-2690 – MCS Rotary encoder 1 initialization failure
- Okuma Alarm B-2691 – MCS Rotary encoder 1 error
- Okuma Alarm B-2692 – MCS Linear scale 4 initialization failure
- Okuma Alarm B-2693 – MCS Linear scale 4 error
- Okuma Alarm B-2694 – MCS Linear scale 3 initialization failure
- Okuma Alarm B-2695 – MCS Linear scale 3 error
- Okuma Alarm B-2696 – MCS Linear scale 2 initialization failure
- Okuma Alarm B-2697 – MCS Linear scale 2 error
- Okuma Alarm B-2698 – MCS Linear scale 1 initialization failure
- Okuma Alarm B-2699 – MCS Linear scale 1 error
- Okuma Alarm B-2700 – No workpiece confirmation error
- Okuma Alarm B-2701 – Sequencer Error
- Okuma Alarm B-2702 – Spindle command during C-axis connection
- Okuma Alarm B-2703 – Chucking miss
- Okuma Alarm B-2704 – Chucking miss air off order impossible
- Okuma Alarm B-2705 – Tailstock quill over advance
- Okuma Alarm B-2706 – Polygon cutting command condition
- Okuma Alarm B-2707 – Invalid command during polygon cutting
- Okuma Alarm B-2708 – Invalid rotation tool gear
- Okuma Alarm B-2709 – Sub-spindle synchronization interlock
- Okuma Alarm B-2710 – Sub-spindle synchronization cutting
- Okuma Alarm B-2711 – Door open
- Okuma Alarm B-2712 – ATC no spec.
- Okuma Alarm B-2713 – Invalid ATC syntax
- Okuma Alarm B-2714 – Invalid ATC TC no.
- Okuma Alarm B-2716 – Invalid ATC TL no.
- Okuma Alarm B-2717 – Invalid ATC MT no.
- Okuma Alarm B-2718 – Invalid ATC MG no.
- Okuma Alarm B-2719 – Invalid ATC command
- Okuma Alarm B-2720 – M06/M228 interlock
- Okuma Alarm B-2721 – Turret number mismatch
- Okuma Alarm B-2722 – Robot/Loader request illegal
- Okuma Alarm B-2723 – ATC next tool preparation interlock
- Okuma Alarm B-2724 – Invalid ATC sub arm
- Okuma Alarm B-2725 – Invalid RS tool L/M
- Okuma Alarm B-2726 – Magazine encoder read
- Okuma Alarm B-2727 – Magazine rotation interlock
- Okuma Alarm B-2728 – Invalid magazine tool no.
- Okuma Alarm B-2729 – No magazine return pot
- Okuma Alarm B-2730 – Tool insertion interlock
- Okuma Alarm B-2732 – Tailstock sleeve position data error
- Okuma Alarm B-2733 – Coolant flow
- Okuma Alarm B-2734 – Coolant level
- Okuma Alarm B-2735 – Spindle low rotation command
- Okuma Alarm B-2736 – SVP time constant switching no spec.
- Okuma Alarm B-2737 – Invalid tailstock switch position
- Okuma Alarm B-2738 – Synchronous hobbing interlock
- Okuma Alarm B-2739 – Invalid synchronous hobbing mode
- Okuma Alarm B-2740 – Incorrect magazine tool data
- Okuma Alarm B-2741 – Touch setter unlock time over
- Okuma Alarm B-2742 – Setup switch ON
- Okuma Alarm B-2743 – Irregular coolant level
- Okuma Alarm B-2744 – Tool breakage
- Okuma Alarm B-2745 – Low high-pressure coolant pressure
- Okuma Alarm B-2746 – Hydraulic oil unit error
- Okuma Alarm B-2747 – Index disable position
- Okuma Alarm B-2749 – Hydraulic oil level lower limit
- Okuma Alarm B-2750 – Tool monitoring unit error detection
- Okuma Alarm B-2751 – Coolant/Oil mist command
- Okuma Alarm B-2752 – Air pressure
- Okuma Alarm B-2754 – Invalid coolant command
- Okuma Alarm B-2755 – Semi-dry unit error
- Okuma Alarm B-2756 – Actual tool data setting
- Okuma Alarm B-2757 – Oil mist unit error
- Okuma Alarm B-2758 – Invalid position data
- Okuma Alarm B-2759 – Coolant discharge error
- Okuma Alarm B-2760 – Sub-spindle rotation tool interlock
- Okuma Alarm B-2761 – W-axis overlap mode
- Okuma Alarm B-2762 – Chucking miss
- Okuma Alarm B-2763 – Coolant filter
- Okuma Alarm B-2764 – Coolant error
- Okuma Alarm B-2765 – Chip conveyer filter clogged
- Okuma Alarm B-2766 – Invalid M-tool spindle command
- Okuma Alarm B-2767 – M-spindle low rotation interlock
- Okuma Alarm B-2768 – Program check mode interlock
- Okuma Alarm B-2769 – Invalid spindle control command
- Okuma Alarm B-2770 – SVP time constant switching command
- Okuma Alarm B-2771 – APC clamp confirmation
- Okuma Alarm B-2772 – APC system mode
- Okuma Alarm B-2773 – APC M command
- Okuma Alarm B-2774 – Thread cutting cycle interlock
- Okuma Alarm B-2775 – Sensor head interlock
- Okuma Alarm B-2776 – M command not completed
- Okuma Alarm B-2777 – Cross rail positioning sensor error
- Okuma Alarm B-2778 – Cross rail motor overload
- Okuma Alarm B-2779 – Axis lube motor overload
- Okuma Alarm B-2780 – Axis lube pressure ON confirmation
- Okuma Alarm B-2781 – No AT command
- Okuma Alarm B-2782 – Axis lube pressure OFF confirmation
- Okuma Alarm B-2783 – Oil hole motor overload
- Okuma Alarm B-2784 – Invalid MT command
- Okuma Alarm B-2785 – Invalid AT command
- Okuma Alarm B-2786 – No S command
- Okuma Alarm B-2787 – No SB command
- Okuma Alarm B-2788 – Invalid SB command
- Okuma Alarm B-2789 – Coolant tank filter clogged
- Okuma Alarm B-2790 – Shower coolant motor overload
- Okuma Alarm B-2791 – M spindle head cooling unit
- Okuma Alarm B-2792 – Invalid RH command
- Okuma Alarm B-2793 – Incorrect attachment index position
- Okuma Alarm B-2794 – Mist air lube unit
- Okuma Alarm B-2795 – Warming up error
- Okuma Alarm B-2796 – Sequence restart
- Okuma Alarm B-2797 – Axis interlock release
- Okuma Alarm B-2798 – Invalid BC command
- Okuma Alarm B-2800 – Alarm detected from externally connected device
- Okuma Alarm B-2801 – Turret rotation interlock
- Okuma Alarm B-2802 – Invalid long boring bar command
- Okuma Alarm B-2803 – ATC tool data setting
- Okuma Alarm B-2804 – Attachment control
- Okuma Alarm B-2805 – Limit confirmation impossible
- Okuma Alarm B-2806 – Door interlock
- Okuma Alarm B-2807 – Invalid M code
- Okuma Alarm B-2848 – Chip conveyer overload
- Okuma Alarm B-2849 – Sensor unit in interference range
- Okuma Alarm B-2850 – External request interlock
- Okuma Alarm B-2851 – Machine change M-code
- Okuma Alarm B-2852 – Hand open/close interlock
- Okuma Alarm B-2853 – Teaching operation interlock
- Okuma Alarm B-2854 – Machine linked M-code
- Okuma Alarm B-2855 – Coolant filter
- Okuma Alarm B-2856 – Coolant motor overload
- Okuma Alarm B-2857 – UNUSABLE M-code
- Okuma Alarm B-2858 – Hand slide advance interlock
- Okuma Alarm B-2887 – Coupling device interlock
- Okuma Alarm B-2888 – Lube tank level
- Okuma Alarm B-2890 – Workpiece clamp miss
- Okuma Alarm B-2891 – Tailstock air miss
- Okuma Alarm B-2892 – Unable to execute air shut-off command
- Okuma Alarm B-2893 – Hydraulic oil controller faulty
- Okuma Alarm B-2894 – Spindle lubricant controller error
- Okuma Alarm B-2895 – Coolant controller error
- Okuma Alarm B-2896 – No touch setter
- Okuma Alarm B-2897 – Unloader no spec.
- Okuma Alarm B-2898 – Unloader interference position
- Okuma Alarm B-2899 – Gauge error
- Okuma Alarm B-2900 – DIRECTION V variable
- Okuma Alarm B-2901 – Direction Check Address
- Okuma Alarm B-2902 – DIRECTION Data operation
- Okuma Alarm B-2903 – DIRECTION Character use
- Okuma Alarm B-2904 – DIRECTION Numerical data
- Okuma Alarm B-2905 – DIRECTION Parameter/point
- Okuma Alarm B-2906 – DIRECTION Register
- Okuma Alarm B-2907 – DIRECTION F
- Okuma Alarm B-2908 – DIRECTION E
- Okuma Alarm B-2909 – DIRECTION Sequence no.
- Okuma Alarm B-2910 – UNUSABLE G-code
- Okuma Alarm B-2911 – UNUSABLE M-code
- Okuma Alarm B-2912 – UNUSABLE Address character
- Okuma Alarm B-2913 – UNUSABLE Mnemonic
- Okuma Alarm B-2914 – UNUSABLE Left side direction
- Okuma Alarm B-2915 – EXPRESSION Calculation
- Okuma Alarm B-2916 – EXPRESSION Syntax
- Okuma Alarm B-2917 – EXPRESSION Right side
- Okuma Alarm B-2918 – EXPRESSION Left side
- Okuma Alarm B-2919 – EXPRESSION Buffer over
- Okuma Alarm B-2920 – VARIABLE Buffer over
- Okuma Alarm B-2921 – PROGRAM DIRECT Program name
- Okuma Alarm B-2922 – PROGRAM DIRECT V variable
- Okuma Alarm B-2923 – PROGRAM DIRECT Character use
- Okuma Alarm B-2924 – PROGRAM DIRECT G-code
- Okuma Alarm B-2925 – BRANCH Sequence name
- Okuma Alarm B-2926 – BRANCH Condition
- Okuma Alarm B-2927 – Parameter setting illegal
- Okuma Alarm B-2928 – Parameter playback impossible
- Okuma Alarm B-2929 – Register setting impossible
- Okuma Alarm B-2930 – Program plus var. limit over
- Okuma Alarm B-2931 – Program minus var. limit over
- Okuma Alarm B-2932 – Program request illegal
- Okuma Alarm B-2933 – Program request impossible
- Okuma Alarm B-2934 – Program external request impossible
- Okuma Alarm B-2935 – No program selection
- Okuma Alarm B-2936 – No Program
- Okuma Alarm B-2937 – Program end code
- Okuma Alarm B-2938 – Program analysis complete
- Okuma Alarm B-2939 – SUB PROGRAM stack
- Okuma Alarm B-2940 – SUB PROGRAM Program name
- Okuma Alarm B-2941 – SUB PROGRAM Buffer over
- Okuma Alarm B-2942 – Command impossible while running
- Okuma Alarm B-2943 – Data file read
- Okuma Alarm B-2944 – Comment End Code Not Found
- Okuma Alarm B-2945 – Equal does not exist
- Okuma Alarm B-2946 – No spec.
- Okuma Alarm B-2948 – DIRECTION Y
- Okuma Alarm B-2949 – DIRECTION Z
- Okuma Alarm B-2950 – DIRECTION D
- Okuma Alarm B-2951 – DIRECTION L
- Okuma Alarm B-2952 – DIRECTION SU
- Okuma Alarm B-2953 – DIRECTION Torque limit
- Okuma Alarm B-2954 – PROGRAM DIRECT M-code
- Okuma Alarm B-2955 – PROGRAM DIRECT Equal
- Okuma Alarm B-2956 – Machine change M-code
- Okuma Alarm B-2957 – G22 Feed Command Is Zero
- Okuma Alarm B-2958 – Main sequence
- Okuma Alarm B-2959 – Barrier limit
- Okuma Alarm B-2960 – User reserve code
- Okuma Alarm B-2961 – Calculation function no spec.
- Okuma Alarm B-2962 – Subscript function no spec.
- Okuma Alarm B-2964 – NC program selection
- Okuma Alarm B-2965 – EXPRESSION subscript
- Okuma Alarm B-2966 – M code time over
- Okuma Alarm B-2967 – Cycle time over
- Okuma Alarm B-2968 – Program selection
- Okuma Alarm B-2969 – G23 FEED
- Okuma Alarm B-2969 – G23 Feed Command Is Zero
- Okuma Alarm B-2970 – DIRECTION X
- Okuma Alarm B-2971 – DIRECTION I
- Okuma Alarm B-2972 – DIRECTION J
- Okuma Alarm B-2973 – DIRECTION K
- Okuma Alarm B-2974 – PROGRAM DIRECT hexadecimal data
- Okuma Alarm B-2975 – PROGRAM DIRECT character string
- Okuma Alarm B-2976 – Stopper position data illegal
- Okuma Alarm B-2977 – Program selection unsuitable
- Okuma Alarm B-2978 – DIRECTION V
- Okuma Alarm B-2979 – DIRECTION C
- Okuma Alarm B-2980 – No decimal point
- Okuma Alarm B-2981 – DIRECTION Q
- Okuma Alarm B-2982 – Time over
- Okuma Alarm-B 2362 NOSE-R COMP. Cancel G00 G01
- Okuma Alarm-B 2362 NOSE-R COMP. Cancel G00 G01
- Okuma Alarm-B 2424 MULTI-MACHINING CYCLE Feed G94
- Okuma Alarm-B 2466 Unable to issue M100 command during Nose-R comp.
- Okuma Alarm-B 2597 G15 command
- Okuma Alarm-B 2957 G22 feed
